NTSB: Amtrak Washington Train Doing 80 MPH In 30 MPH Zone

Posted by:

Cars from an Amtrak train lay spilled onto Interstate 5 below as some train cars remain on the tracks above on Monday in DuPont, Wash.

Elaine Thompson/AP

hide caption

toggle caption

Elaine Thompson/AP

Cars from an Amtrak train lay spilled onto Interstate 5 below as some train cars remain on the tracks above on Monday in DuPont, Wash.

Elaine Thompson/AP

The National Transportation Safety Board says an Amtrak passenger train that derailed from an overpass south of Tacoma, Wash., leaving at least three people dead, was traveling at 80 mph in a 30 mph zone.

At a news conference late Monday Pacific Time, NTSB board member Bella Dinh-Zarr said that the speed of the train at the time of the accident had been determined by downloading the Event Data Recorder from the train’s rear locomotive.

Train 501 of Amtrak’s Cascades service from Seattle to Portland was on its maiden run of a faster-speed service when it careened off the track at DuPont on Monday. In addition to the three people killed in the accident, 23 others were injured, Washington State Patrol spokesman Dan Hall said. Ten of those hurt were in serious condition, four had moderate injuries and another nine suffered minor injuries, he said.

Asked if the NTSB had any theories as to why the train was traveling so fast in the 30 mph track zone, Dinh-Zarr told reporters, “It’s too early to tell.”

She said one of the questions investigators hoped to answer in interviews with the crew was whether the engineer was aware of the speed limit in the corridor where the accident occurred.

Dinh-Zarr said the NTSB was checking to see if the Positive Train Control, or PTC, was installed on the stretch of track in question. PTC is a system designed to automatically stop a train in certain dangerous situations.

As NPR’s Martin Kaste and Colin Dwyer reported on Monday, it was the first time the train had plied a new, more direct and faster route “on tracks known as the Point Defiance Bypass, which are owned by the Sound Transit agency. The Washington State Department of Transportation says the Federal Railroad Administration funded and reviewed recent upgrades to the tracks.”

The new route eliminates speed-sapping corners and tunnels that were present on the more scenic route that ran along Puget Sound.

In total, the project’s budget was nearly $181 million.

The Washington State Department of Transportation had billed the service “as a more frequent, more reliable, and faster Amtrak Cascades service.”

Amtrak Engineer Charged In Deadly 2015 Philadelphia Train Crash

Amtrak Train Derails On Overpass In Washington State, Killing 3

But some local officials were skeptical of the new service, questioning whether the trains would be safe at higher speeds. Earlier this month, the mayor of Lakewood, a suburb of Tacoma, predicted a deadly accident.

Mayor Don Anderson said the addition of grade separations, such as overpasses, to keep trains, cars and pedestrians separated, was needed.

“Come back when there is that accident, and try to justify not putting in those safety enhancements, or you can go back now and advocate for the money to do it, because this project was never needed and endangers our citizens,” Anderson was quoted by KOMO News.

Last month, the NTSB issued a report saying Amtrak had a “deficient” safety culture.

“Amtrak’s safety culture is failing and is primed to fail again, until and unless Amtrak changes the way it practices safety management,” NTSB Chairman Robert Sumwalt said in a statement on Nov. 14.

On May 12, 2015, an Amtrak Northwest Regional train derailed In Philadelphia, killing at least seven people and injuring more than 200 passengers. A year later, NTSB concluded that a distracted engineer was to blame.

Article source: https://www.npr.org/sections/thetwo-way/2017/12/19/571865743/ntsb-amtrak-washington-train-doing-80-mph-in-30-mph-zone?utm_medium=RSS&utm_campaign=news

  Related Posts